» Your pool can be easily emptied and stored in a safe place during the winter. However, many people choose to leave their pool up year round. In areas where freezing temperatures occur, there is risk of ice damage. It is recommended to drain, disassemble and store the pool in a safe place when temperatures drop below 32 degrees Fahrenheit. See "How To Drain Your Pool" section.
Clean pool water thoroughly (If Easy Set Pool make sure the top ring is properly inflated).
Remove the skimmer (if applicable) or any accessories attached to the threaded strainer connector. Replace strainer grid if necessary. Be sure all accessories parts are clean and completely dry before storage.
Plug the Inlet and Outlet fitting from the inside of the pool with the plug provided (sizes 10' and 12'). Close the Inlet and Outlet Plunger Valve (15', 18', and 24').
Remove the ladder (if applicable) and store in a safe place. Be sure the ladder is completely dry before storage.
Remove the hoses that connect the pump and filter to the pool.
Add appropriate winter chemicals. Consult your local pool dealer as different regions vary greatly.
Cover pool with Intex Pool Cover. IMPORTANT: INTEX POOL COVER IS NOT A SAFETY COVER.
Clean and drain pump, filter housing and hoses. Remove and discard old filter cartridge (keep a spare cartridge available for next season).
Bring pump and filter parts indoors and store in a safe and dry area, preferably heated.
STORING POOL FOR WINTER
After draining pool, dry pool liner completely (100%). Sprinkle talcum powder on liner to prevent vinyl from sticking together and to absorb any water you may have missed.
Roll pool liner to avoid creases and relocate to storage area. Place it in original carton if you saved it.
Keep all small parts together with filter pump, manual, and pool, and then place in an area that will remain at room temperature throughout the storage season.
» Yes, in some cases certain types of hardy grass such as Bermuda or St. Augustine can grow through the liner. Before setting up your pool, it is recommended that you clear the area of these types of hardy grasses. INTEX will not be held responsible for grasses that may grow through the ground cloth and / or pool liner, as this is not a manufacturing defect. A ground cloth or tarp may be helpful in preventing this from occurring.
» No. With proper chemicals and filter cartridge replacement, the pump will keep the pool clean from suspended water particles. A pool vacuum should be used to clean the walls and bottom of the pool. Additionally the INTEX KRYSTAL CLEAR TM Saltwater System and maintenance kits will keep your pool clean from algae and bacteria. Depending on the local characteristics of your water condition, it may be desirable to add water softeners, clarifiers, or algaecides.
» Water condition varies from country to country, states, region, and within specific zones and areas. In some regions the water could be "hard water", this is because the water contains excessive minerals, such as calcium and magnesium, thus causing the water to adopt a milky color. Check your local pool supply store for advice on water treatment and balance.
» Yes, you can upgrade your filter pump to a larger model. Make sure the hose fittings are compatible. There are two (2) hose sizes, model 603/604/637/637R/638/638R use 1-1/4” (32mm) hose size (part# 10116 or #11149), and model 635T/636T/633T/634T/FP621/FP622/SF10110/10220/SF15110/15220/SF20110/20220/CG Model 8111 use 1-1/2” (38mm) hose size (part# 11009). You will need two (2) hose adaptors B (part# 10722) when upgrading from 1-1/4” (32mm) to 1-1/2” (38mm) hose fittings. The flow rating of any replacement filter must not exceed the maximum flow rating of the strainer grid on the suction side of filtration system. The maximum flow of the strainer grid is embossed on the strainer grid.
» Yes, the pump is designed to be used with INTEX vacuum system (#58947/58948/ 58949/18947/18948/18949) only. 58947/18947 and 58949/18949 require a minimal flow of 800 gph (3028 lph), and 58948 requires a minimal flow of 2,000 gph (7,570 lph).
» We recommend circulating the entire pool water once every day; refer to the table attached or the instructional DVD video for operating time. You may extend the operating hours depending on water, ambient conditions and heavy pool usage.
Note: we do not suggest operating the pump for more than 8 hours per day.
» See Trouble Shooting Guide in the Owner’s Manual. Also check the filter cartridge. If it is dirty the water flow will be much less powerful. Replace the cartridge. Also, check the hoses for any pinholes causing water leakage. And check for debris caught in the grating where the hose connects to the filter pump. The hose clamps may also be loose.
» Empty the pool, use a soft brush, mild detergent and water to remove algae stains from the pool liner. Thoroughly rinse and dry before refilling or storage.
» If a product is purchased directly from Intex www.intexcorp.com and it is found to be defective within 90 days of purchase, call Intex Consumer Service and an Intex agent will initiate a claim for the defective product. Once the claim is processed and approved the replacement is shipped within two business days. For a second replacement within the initial 90 day service period, Intex requires that a claim be filed for defective parts and that the defective item be returned at the consumer’s expense. Call (800) 234-6839 for further assistance and information.
» Most replacement parts for Intex products are available directly from Intex at www.intexstore.com or contact us direct at (800) 234-6839. We accept Visa, Mastercard, American Express and Discover only, no checks, money orders or C.O.D.s.
» A PVC or silicon based glue for repairing camping mats, tents, shoes, inflatable boats, etc are suitable for INTEX pools.
» Review the Trouble Shooting Guide in your Owner's Manual.
» Estimated filter pump life is approximately 2,000 hours, which is about 3 summer seasons of normal usage.
» No, due to various local, state, national and international standards, the filter pump is not to be operating if pool is in use and/or occupied, although it is safe and has complied with UL, CSA, ETL, and EN safety standards.
» See attached file
» Yes, for hygienic purposes we recommend a filter pump be used with all INTEX 8' or larger above ground pools.
» Orders are shipped within 2-3 business days once the order is placed. Orders will be shipped by regular mail or Fed EX (depending on the size of the order). Therefore, transit time will be determined based on your location and shipping method.
» If your e-mail address was provided at the time the order was placed, and your order was shipped by Fed EX, you will receive an e-mail confirmation with the tracking number. You can then go to the Fed EX website to track the package.
» No. The pump is not designed for this purpose.
» A standard shipping and handling charge is calculated into every order, regardless of the shipping method.
» Yes. Intex will accept replacement part orders, accessory orders, and warranty questions from Canadian consumers. For replacements on items other than Above Ground Pools and specific airbeds, please refer back to the original place of purchase. To order replacement parts please call 800-234-6839 or go to www.intexcorp.com.
» Yes, the filter pump comes with a limited written warranty included in your Owner's Manual which covers all manufacturing defects in material and workmanship.
» It takes 2-3 business days to process the order and 2 additional business days in transit for Fed EX to ship. This is the fastest method of shipping that we offer. There is no next-day air service available. The package will be received within approximately 3-5 business days. All shipments to Canada will go by standard (ground) Fed EX or regular mail.
» Keep all debris out of pool (keep covered) with a debris pool cover, and maintain the proper pH balance and chlorine level.
» No, the pump is to be returned to INTEX, freight prepaid at the consumers expense. INTEX will pay the cost to send a replacement pump. Please contact Intex Consumer Service for instructions at (800) 234-6839. (See Owner’s Manual Limited Warranty). (US/Canada)
» No, however the valves need to be closed for filter cartridge replacement.
» No. This will invalidate the filter pump warranty and INTEX will not be responsible for any consequences that might result from opening the motor housing for any reason. Personal injury may result if reassembly is done improperly.
» Excessive use of pool chemicals can cause the color of the inside wall printing to fade away faster, like a heavy chlorinated public swimming will cause a bathing suit color to fade.
» No. After the pool has been filled with water, air can be released from the top of the filter chamber and then the motor can be turned on. See instruction in Owner's Manual.
» Due to variations in ambient temperature, PVC parts may become stiffer or softer. To facilitate the connection of the hoses to the black protruding hose connectors on the pool wall, you may use soapy water solution (mix 6 drops of dish detergent in 1/2 a cup of water) to lubricate the hoses and the black protruding hose connectors. Continue installation per owner's manual. Do not use lubricants such as machine oil, industrial oil, or house grease.
» 30 Days from the date of delivery as stated on the shipping invoice (except items that come with a written warranty).
» Yes, depending on the model, INTEX filter pumps meet UL, CSA, ETL, EN and AS/NZ Standards.
» No, payment can only be made using Visa, Master Card, Discover or American Express.
» No. The shipping costs have already been incurred at your request and therefore are non-refundable.
» The two ratings relate to different methods of measuring the flow of water from the pump. The Pump Flow Rate is a measurement widely used in the industry by manufacturers to rate the flow of water directly from the pump. This measures the pump’s true capacity to move water.
The System Flow Rate measures the amount of water that the pump moves when it is hooked into a pool system and has to push water through several hoses, suction fittings, filter cartridges and even against the force of gravity when the water is pushed from the filter back up to the pool. For reference, the strainer grids in your pool are always rated in terms of the System flow rate, since they are part of the pool system. Because of the extra force required, the System Flow Rate will always be less than the Pump Flow Rate.
All Intex pools take this difference into account, and the pump that comes with your pool is designed to easily keep your pool water clean and sparkling. The strainer grids rated in terms of the system flow rate.
» Remove and clean with fresh water and dry all components including hoses. Coat the seals, O-Rings and washers with petroleum jelly (see Owner’s Manual for detailed instructions). Store the device and accessories in a dry, indoor storage area preferably between 32 degrees Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius). The original packaging can be used for storage.
» Depending on usage and water conditions, it is recommended that the cartridges be replaced at minimum 2 week intervals. The filter cartridge should be removed and checked at least once a week. It can be partially cleaned by rinsing it off with a garden hose and brush. If it still appears to be dirty, it should be replaced immediately.
» Processing time is approximately 3 business days from the date we receive the product. It is then shipped by Fed EX Ground from Long Beach CA. Therefore, transit time will be determined by your location.
» Occasionally, petroleum jelly may be applied to the “O-Ring” located underneath the top filter cover to minimize seal cracking. Check hoses for leaks and replace if needed. Also make sure you've cleaned or replaced filter cartridges as recommended in the Owners Manual.
» Yes, call Consumer Service Department at (800) 234-6839 to place a phone order, 8:30 AM to 5:00 PM PST, Monday through Friday, or visit our website at www.intexcorp.com (US/Canada)
» No. Mainly because of the electrical connections' location to the water chamber, and the fact that improper repair may result in electrocution, injury and/or death.
» 110-120V (depending on models), single phase AC. (Which is normal household electricity).
» No. The 0.25 inch (0.63 cm) gap or the two dents are mold-tooling marks (see attached pictures). Water leakage is mainly caused by a missing O-ring, the O-ring is not sitting properly and/or cartridge cover or collar not properly secure and tighten.
» The 1-1/4” (32mm) hose size is the correct hose for these pumps. Make sure the white sleeves from the previous hoses are removed from the black protruding hose connectors and also from the filter pump hose connectors. See attached picture:
» There are no special policies for gifts. Our replacement polices apply the same to purchased items and gifts and a copy of the validated sales receipt is required.
» GFCI (Ground Fault Circuit Interrupter) is a device that protects people from serious injury due to electric shock.
GFCI’s constantly monitor electricity flowing in the circuitry. If the electricity flowing into the circuit differs by even a slight amount from that returning, the GFCI will quickly shut off the current flowing through that circuit.
The advantage of using a GFCI is that it can detect even small variations in the amount of current flowing through an electrical product, even amounts too small to activate a fuse or circuit breaker. GFCI’s work quickly, so they can help protect consumers from severe electric shocks and electrocution while most common circuit breakers take far too long to stop the flow of electricity.
» The model of the pump can be located on a gray or silver colored sticker on the side of the system. The label will say “Krystal Clear Model” and there will be a model number next to that.
» 25 feet (7.62 meters) long for 110V-120V AC in North America.
» Yes. The GFCI/RCD should be installed by a licensed electrician.
» U.S. currency.
» No, you must provide a physical address for Fed EX to deliver your package. Fed EX does not deliver to Post Office boxes, APO or PPO addresses.
» It is the consumer’s responsibility to notify Intex within 15 days of receiving a defective or incorrect replacement by calling (800) 234-6839.
» No. A penny or dime can be used to tighten the hose clamps.
» No. Our system does not accept COD (Cash on delivery) or check. We only accept Visa, Mastercard, American Express and Discover credit cards. Pre-paid credit cards can be used if they are from one of these four companies.(for U.S & Canada only)